The Plane –
The plane for this project is loosely based on a miter plane made by Robert Towell of London in the early to mid 19th century. The original plane belongs to my friend Joel Moskowitz of Gramercy Tools and Tools for Working Wood, and I had a chance to take some measurements and photography of the plane several years ago at his shop. Joel, who is an avid historian of woodworking as well as a woodworker and tool collector, did a brief writeup on Towell and the plane on his blog way back then; if you search his blog for ‘mitre’ (his preferred spelling – in the british tradition) you will also find quite a fair bit of other information regarding these planes, which are somewhat of a curiosity in that there isn’t a firm consensus as to what they were originally used for. I’m not going to wade into that debate here – at least not now – but Moskowitz has offered some ideas in his blog.
This is probably not a project I would recommend for a first attempt at making an infill plane – there are several features of its construction that are somewhat advanced, and add quite a bit to its difficulty. Firstly, the one-piece bent sidewalls are tricky to form and fit infills to; Secondly, this is a bevel-up plane design, which requires a two-piece sole construction — one of the more challenging aspects of planemaking to get right in my experience. Having said that, however, this plane does have a lot to interest people who are considering making a plane, as well as those who are perhaps already somewhat experienced planemakers. It should also provide a fairly comprehensive picture of the basic processes necessary for all-dovetailed infill construction by hands. For these reasons, I think it’s a solid candidate for a project writeup – and I’m hoping it will provide a fairly accurate idea of what infill making entails, and some of the choices and problems that can come up in planning and constructing a plane from scratch.
Design – sharpen those pencils and/or clean the lint from your mouse.
The first step in getting the design established is to make some dimensioned drawings, establishing at the very least the major angles and distances necessary to start laying out and cutting the sole and sidewall pieces. I will generally create a mechanical drawing in Adobe Illustrator eventually, but I still prefer to start with graph paper and pencil for most of my construction drawings. This is largely a matter of comfort and preference, though – you should use whatever format you’re most at home with. Here is the rough construction drawing set I am going to be working from:s
The next step for me is making some test bends in my steel bending fixture, establishing the setup I’ll be using and the radius of the curvature of the sidewalls at the rear of the plane. This is necessary to ensure I have the proper layout of the sidewalls, which are all laid out, cut, and filed before the bending happens. While it’s a simple task to calculate the radius of the curve mathematically, there are two problems with using this as the only measurement – one is that the final curves will rarely match up to a perfect semi-circle, such that the final radius will almost always be somewhat shorter than the theoretical one; the second problem is that there is always some degree of stretching and compression of the steel when it’s bent to a curve. The bottom line is that you can get an approximate prediction of the length to allow for the radius, but in my experience it can be off by as much as 3/8″ from the actual results. A test bend using the same thickness of steel is the only reliable means of establishing the necessary length. I use inexpensive cold-rolled steel for these checks, which generally give results within 1/16″ of my final bend – quite close enough for my purposes.
I use a Grizzly compact bending tool, which I mentioned briefly in an earlier post. This isn’t really necessary, however – planemaker Bill Carter, who’s made some of the most beautiful mitres ever produced, uses simple bending forms in a machinist’s vise for all his work. The compact bending tool just adds a degree of simplicity and repeatability that I find helpful if you plan to make more than a couple of planes.
Laying out sidewall dovetails – pins first
Once I have worked out the bend setup, it’s time to generate a dovetail layout template. I do this on graph paper with simple black markings for each of the ‘pins’ on the sidewall. Notice that you only lay out half the plane, in this case from the front edge to the rear centerline – you’ll mark half of the sidewall, then flip the blank and mark the other side from the same template to ensure you have a nice, symmetrical dovetail arrangement. If you enlarge the next photo below, you can see the markings on the graph paper below the steel.
Now it’s time to start preparing the steel flat stock. I’m using 3/16″ O1 steel of 2″ width. Allowing 1/16″ of excess for peening dovetails to the sole, this should give me a final height of 1-15/16″ for the plane. I cover the ‘outside’ face and bottom edge of the steel with layout dye, then mark off the front edges (again, leaving at least 1/16″ excess for peening the front wall on later) and the centerline. Now I use the template to mark the dovetails off at the bottom of the face. You can see the template and the already-marked blank below:
With straight-sided planes, I have some degree of choice as to whether the sidewall dovetails are the ‘pins’ or ‘tails’ — if I use pins here, the sidewalls will drop in to the sole from above; if I use tails, the sidewalls will slide in to the sole from the sides. For a one-piece sidewall like that in this plane miter, however, the sidewalls can only drop in from above, so the decision is effectively made for me – pins it is.
On the face of the stock, I first scribe a line to mark the top of the dovetails – in this case, I have allowed for a 5/16″ sole and 1/16″ of excess, so this line is scribed at 3/8″ from the bottom.
With the template markings transferred to the plane, I use a square to extend the marks up the face of the stock to the line scribed previously. On the bottom edge of the stock, I then mark off the ‘flare’ for the dovetails as they will be seen from the sole of the plane. My habit is to draw my templates to represent the outside of the sidewall, so each pin expands to the inner face at an angle of about 12-15 degrees, which I find to be a nice balance between aesthetics and ease of peining closed. The photo below shows the completed dovetail layout.
At this point, I am ready to cut and file the dovetails as laid out. There will be additional layout for the secondary dovetails later on, as well as the mortises for the bridge – but there is no reason to add to the complexity at this point.